|
USA-SC-COLUMBIA Azienda Directories
|
Azienda News:
- IEC 62056-21 Communications Protocol - SATEC
F – billing period 0-3, 0 (not indicated) for present billing period, 1 for the first previous (last) period, 2 for the second previous billing period, 3 for the third previous billing period The following table lists the OBIS codes used in the EM720 data readouts OBIS Code Unit Description 0 1 0 Billing period counter
- OBIS codes - OneMeter Documentation
It contains 3 elements: OBIS code 1 8 0, counter value 158233 46 and the unit kWh separated with specific characters The OBIS codes corresponds to the type of measurement For example, 1 8 0 corresponds to positive active energy consumed from the grid What does that mean? This is the amount of active energy you consumed since your meter was installed (or its registers were reset) Why 1 8 0?It has been defined in the IEC62056-21 standard (as amended), in which the exact representation of
- OBIS Codes as per IEC62056-61 - Microstar Electric
OBIS Codes as per IEC62056-61 The Object Identification System (OBIS) is Part 61 of IEC62056, which defines the identification codes for commonly used data items in electricity metering equipment The below are the (partial) list of OBIS codes supported by Microstar smart meters* * For reference only Subject to change without notice For the full list of OBIS codes, please refer to the product manual or contact Microstar support
- The OBIS codes meaning on electro meters - Enectiva FAQ
The OBIS code is a unique identification of the registers in the meter’s memory according to IEC 62056-61 Particularly when setting the initial states of the pulse counters, it is important to know which register to write Reactive demand in the last completed demand period in Q1 (Q1) [kvar] 6 5 0: Reactive demand in the last completed demand period in Q2 (Q2) [kvar] 7 5 0:
- How to determine billing scheme | for DLMS smart meters - Gurux
Clause A 3 explains how to handle group F to identify the billing period What I cannot understand is how to determine billing scheme based on billing period counter Let's say, that I have use two schemes - day and month Then, for example, I use OBIS code 1 0 1 8 0 10 Do not trust OBIS codes too match Some meters are using all kind of OBIS codes :-(You must read your meters and check what kind of data they are returning and then make your logic using that info BR, Mikko vstokarev
- OBIS code for IEC 62056 – electricity, current, voltage
The OBIS code is displayed on the electric meter screen together with the measured value, its position depends on the meter model and can be positioned anywhere, usually in a corner List with OBIS code and Description: 5 5 0 Reactive demand in the last completed demand period in Q1 (Q1) [kvar] 6 5 0 Reactive demand in the last completed demand period in Q2 (Q2) [kvar]
- Description of OBIS code for IEC 62056 standard protocol
The OBIS code identifies the corresponding device value It is a text string composed according to the OBIS standard (see IEC 62056-61) Older and simpler variant is the EDIS code This code, for example, does not cover the groups A and B (see further) Reactive demand in the last completed demand period in Q1 (Q1) [kvar] 6 5 0: Reactive demand in the last completed demand period in Q2 (Q2) [kvar] 7 5 0:
- ESPHome IEC 62056-21 Component - Aquaticus
The meter transmits data registers with associated OBIS codes If the transmission has failed (bad checksum or invalid format), the component will try to read data again but this time using a slower transmission speed F - billing period; A, B, and F may be omitted Codes may use hexadecimal digits, for example, code 15 8 0 could be represented as F 8 0 The codes are standardized but devices send a different number of codes To get the second value (date time in this example) use a
- OBIS Identification Codes. Satec expertmeter EM720T
F – billing period 0-99, 0 (or not shown) for present billing period, 1 for the first previous (last) period, 2 for the second previous billing period, and so on The following table lists the OBIS codes used in the EM720 billing data displays
- OBIS-Code Configuration | Lobaro Documentation
OBIS-Code Configuration Object identification system (OBIS) Codes are used to identify the different readings of a smart meter transferred in Smart Message Language (SML), which is a commonly used protocol on D0 optoelectronic interfaces They are described in the international standard IEC 62056-61 billing periods, 255 if not used:
|
|