|
Canada-0-ACCOMMODATIONS Azienda Directories
|
Azienda News:
- Camshaft position sensor error P0340 - The FIAT Forum
Hi Everyone, So here's a long story short I have a mk2 Punto 1 2 16v sporting The exhaust looks like it is causing the airbox to melt I changed the bottom half of the airbox that contains the filter thinking it was caused by a recent overheating issue I had but its now melting the new
- 2007 Fiat Ducato 3. 0 fault code P0340 | FIAT Ducato e-Ducato (Gen 3)
Hi Some weeks ago I got the yellow engine lamp on dash Code reader said P0340 Deletetd the code and move on After a 5-6 faults, it starts works witout codes, but I want to change sensor anyway I ordered a new camshaft position sensor from Hella Installed it, but engine will not start
- No signal from Camshaft Sensor P0340 Fault Code | FIAT Ulysse
P0340 Camshaft Position Sensor “A” Circuit What does this mean? BD Code P0340 refers to This indicates that a problem was detected in the camshaft position sensor circuit Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM Don't just replace the CPS (camshaft position sensor) and think that will definitely fix it
- Fiat 500 Twin Air 0. 9 (2015) – OBD Code P0340 | FIAT 500 (2007+)
Hi All, My Fiat 500 has been acting a little strange over the past two week Last Thursday whilst driving down some residential roads (30 mph) I got a Start Stop Unavailable and Check Engine Light I turned off the car at the lights and the errors went away Since then, the car was driven for
- P0340+p0482+p0683 | FIAT Croma (2005+) | The FIAT Forum
Had a Google come-up with the following … P0340 Camshaft Position Sensor “A” Circuit What does this mean? BD Code P0340 refers to This indicates that a problem was detected in the camshaft position sensor circuit Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM
- rough starting p0340 | FIAT Doblo (Mk1 Mk2) | The FIAT Forum
hi my fiat doblo 1 9 multi jet is taking ages to start I've plugged it into multiecuscan and it comes back with code p0340 cam shaft position sensor will this be the problem? looking at this forum lots of post say crankshaft sensor is the camshaft sensor the same as the crankshaft
- P0340 error that keeps showing up no matter what I fix | FIAT Bravo 2 . . .
No signal from Camshaft Sensor P0340 Fault Code | FIAT Ulysse Hi I recently rebuilt my 2 0 16v HDI engine after timing belt failure but now the car wont start See my post on the Eurovan Forum: Ulysse 2 0 16V JTD 2004 Engine repair project I'm getting the P0340 fault from my PP2000 reader, Screenshots below I have replaced the Cam sensor but
- Camshaft Sensor error code P0340 | FIAT Ducato (Gen 2)
It doesnt sound rough or cut out or anything but it keeps logging the P0340 error code I have checked all the wiring and replaced the sensor the gap between the teeth and the sensor is about 2-3 mm
- Ducato Engine Failure | FIAT Ducato e-Ducato (Gen 3)
A week ago in Portugal my 2016 model 2 3 multi jet Ducato powered down completely whist cruising a autoroute in my Hymer motorhome Rescued and taken to a Fiat garage who ran a diagnostic check and suggested there is a P0340 fault The garage is unable to do the work and the vehicle has to be
|
|