|
Canada-0-DECALS Azienda Directories
|
Azienda News:
- Difference between Cisco K8 and K9 images
Q What do K8 and K9 designators refer to in Cisco product part numbers? A In general, the K8 and K9 designators in Cisco product part numbers refer to unrestricted and restricted encryption respectively (Table 2) These designators have been defined by Cisco to be used in product part numbers of products that support encryption Table 2
- Is anyone can help me how to download AIR-AP3800-K9-ME-8-10-196-0. tar . . .
The software version you're looking for, AIR-AP3800-K9-ME-8-10-196-0 tar, is indeed the "Mobility Express" (ME) image, which is exactly what you need to transform this AP into a standalone system without the need for an expensive physical wireless controller
- I want to know how to enable SSH to access points via the wireless . . .
I want to know how to enable SSH to access points via the wireless controller GUI and CLI, and then how to set the login password for those access points WLC Model ==> CISCO SYSTEMS INC 5500 Series AIR-CT5508 50-K9
- AIR-CAP3602I-A-K9 factory reset not working - Cisco Learning Network
Hello everyone! I'm new to this group and not very well versed yet in Cisco wireless equipment I'm actually working on my CCNA for routing switching right now Someone offered me a couple of wireless AP's that they had no use for, so I figured it couldn't hurt to get in some practice with wireless However I've run into a slight issue I can't get them to reset to factory settings! I've
- Problem installing packages: NCS540-iosxr-k9-6. 6. 3
I am trying to install NCS540-iosxr-k9-6 6 3 tar Packages, but keep getting this messages: PS: I have installed this image on 5 other router (via cli ) which are successful and working fine, but i am finding it extremely difficult for this particular router (EFI Usb boot) i don't know what could possible be the problem
- Payload file is missing while upgrading CUE - Cisco Learning Network
I am trying to upgrade my NM-CUE to 7 0 6 The download completed fine but the language pack installation is the problem i tried some technics like using the current license file in the CUE that didn't work Any help with this ?
- In CML 2. 7. 2, When adding nodes, I could not find the IOS-XRv, but . . .
In the folder \node-definitions\ you'll find the IOS XRv node definition (iosxrv yaml file) and in the folder \virl-base-images\iosxrv-6-3-1\ you'll find the IOS XRv image (iosxrv-k9-demo-6 3 1 qcow2 file) Please follow these instructions from my buddy @Jim Leko on how to manually import them into CML and you should be good to go
- What is No pay load encryption on IOS mean?
To satisfy the import requirements of those countries, the `npe' universal image does not support any strong payload encryption This image supports security features like Zone-Based Firewall, Intrusion Prevention through SECNPE-K9 license Expand Post Selected as Best Like LikedUnlike Reply 1 like Loc Nguyen
- AIR-AP2802I-B-K9 - Cisco Learning Network
Access points are showing up but could not connect to the controller due to "invalid license in configuration request" As per Cisco website , this is regarding the regulatory domain is there a way we can replace the two AP's with AIR-AP2802I-E Instead of AIR-AP2802I-B so teh AP's are using the correct regulatory domain
- How to configure routing on a Cisco 1941 using Vlans, Router-on-a-stick . . .
I recently bought a Cisco 1941 to use as part of my lab Loving it so far, but when I tried a more complex configuration, it didn't work Here is what I use Interface g0 0 0 is my WAN interface which I put on the Vlan 2 since it's a L2 interface It gets a DHCP ip address from my residential gateway I'll reserve it later Interfaces g0 0 and g0 1 are part of an EtherChannel group, connected
|
|